← Back to Welder (Health Services)
⏱️

Free Welder (Health Services) Mock Test

Test your knowledge under timed conditions. Get scored results instantly — no sign-up required.

❓
Questions
15
⏳
Time Limit
15 min
📝
Format
Multiple Choice

Instructions

  • Answer all 15 questions within 15 minutes.
  • You can skip questions and come back to them later.
  • The timer starts when you click “Start Mock Test”.
  • Your score will be shown immediately after submission.
  • Sign up free to see detailed rationales for every answer.

Timer starts when you click the button.

About This Mock Test

The Free Mock Test for Welder (Health Services) (292/2025) is designed to help candidates prepare effectively for the Welder (Health Services) exam. This mock test focuses on assessing your practical knowledge and skills related to welding within health service environments, ensuring you are well-equipped to meet the exam requirements. With a medium difficulty level, this test simulates the real exam conditions to provide a reliable measure of your readiness.

Exam Pattern

  • Duration: 15 minutes
  • Number of Questions: 15
  • Difficulty Level: Medium
  • Passing Percentage: 75%

Topics Covered

  • Hand Tools

Why Take This Mock Test?

  • Gain familiarity with the exam format and question types specific to the Welder (Health Services) exam.
  • Identify your strengths and areas for improvement within the Hand Tools module.
  • Build confidence by practicing under timed conditions similar to the actual test.
  • Enhance your chances of success by meeting the 75% passing criteria through targeted preparation.

Ready to boost your preparation? Take the free Welder (Health Services) mock test now and take a confident step towards acing your exam.

📋 Preview All 15 Mock Test Questions

Q1. Which characteristic of a scriber makes it especially suitable for marking metal surfaces compared to a pencil?

  1. Its ability to leave a permanent ink mark
  2. Its sharp tip that scratches the metal surface
  3. Its rubber grip for comfortable handling
  4. Its magnetic base for stability

Q2. Compare a steel rule with a hook end and a steel rule with a fixed end. Which statement correctly describes their difference in measuring external dimensions?

  1. Hook end rules measure external dimensions by hooking onto the edge, fixed end rules measure from the end of the rule.
  2. Fixed end rules are used only for internal measurements, hook end rules only for depth.
  3. Hook end rules are less accurate than fixed end rules for external measurements.
  4. Fixed end rules have a sliding scale, hook end rules do not.

Q3. What is the primary purpose of a steel rule in welding tasks?

  1. To measure and mark dimensions accurately on metal surfaces
  2. To weld two metal pieces together
  3. To grind and smooth metal edges
  4. To heat metal before welding

Q4. A welder needs to measure a metal piece that is 7 and 5/16 inches long using a steel rule. How should the welder read the measurement on the steel rule?

  1. Locate the 7-inch mark and then count 5 small graduations after it
  2. Locate the 7-inch mark and then count 3 small graduations after it
  3. Locate the 5-inch mark and then count 16 small graduations after it
  4. Locate the 7-inch mark and then count 16 small graduations after it

Q5. A welder needs to measure a length of 37.5 cm accurately using a steel rule graduated in millimeters. How many millimeter marks will the welder count on the steel rule to measure this length?

  1. 375 mm
  2. 37.5 mm
  3. 3,750 mm
  4. 0.375 mm

Q6. A welder needs to mark a straight line 150 mm from the edge of a steel plate using a scriber and a steel ruler. Which of the following steps is the correct procedure?

  1. Place the ruler along the edge, measure 150 mm, then use the scriber to scratch a line at that point.
  2. Use the scriber to measure 150 mm, then draw a line freehand.
  3. Mark 150 mm with a pencil, then use the scriber to trace over the pencil line.
  4. Place the ruler at 150 mm from the edge and weld along the edge.

Q7. Compare two steel rules: one stored in a dry, oiled condition and the other left exposed to moisture without maintenance. Which statement correctly describes their expected condition after 6 months?

  1. Both will remain in similar condition due to steel's natural resistance
  2. The oiled rule will be rust-free and accurate; the exposed rule will likely have rust and measurement errors
  3. The exposed rule will be more accurate due to natural aging
  4. The oiled rule will become sticky and unusable

Q8. A welder uses a steel rule that has a 0.5 mm worn-out section near the 50 cm mark. If the welder measures a piece as 50 cm using this rule, what is the actual length of the piece?

  1. 49.5 cm
  2. 50.0 cm
  3. 50.5 cm
  4. 51.0 cm

Q9. In a welding workshop, a steel rule is marked with graduations on both edges: one in inches and the other in centimeters. What is the primary benefit of this type of steel rule?

  1. Allows measurement of both metric and imperial units without changing tools
  2. Increases the length of the steel rule
  3. Improves the durability of the steel rule
  4. Provides a flexible measuring surface

Q10. What is the primary reason for regularly cleaning and oiling a steel rule used in welding measurements?

  1. To prevent rust and ensure accurate measurements
  2. To make the steel rule look shiny and new
  3. To increase the length of the steel rule
  4. To reduce the weight of the steel rule

Q11. A welder needs to mark a metal sheet for a cut exactly 125 mm from the edge. Using a steel rule marked in millimeters, which of the following steps is the most accurate method?

  1. Place the zero end of the steel rule at the edge and mark at the 125 mm graduation
  2. Place the 10 mm mark at the edge and mark at the 135 mm graduation
  3. Estimate the 125 mm point by eye without using the steel rule
  4. Use the steel rule upside down and mark at the 125 mm graduation

Q12. A steel rule is 1 meter long and has developed slight rust spots. After cleaning and oiling, the rule's markings appear less visible. What is the best practice to maintain both protection and readability?

  1. Apply a thin layer of light oil and wipe off excess to keep markings visible
  2. Apply thick oil to cover the entire surface for maximum protection
  3. Avoid oiling and only clean with water to preserve markings
  4. Use abrasive tools to remove rust and repaint the markings

Q13. A steel rule is marked in millimeters and centimeters. If a welder measures a length of 7.8 cm on a metal piece, what is the equivalent measurement in millimeters?

  1. 78 mm
  2. 7.8 mm
  3. 0.78 mm
  4. 780 mm

Q14. A welder uses a scriber to mark a line 75 mm from the edge of a metal sheet. If the metal sheet is 300 mm wide, what percentage of the sheet's width is the marked distance from the edge?

  1. 25%
  2. 20%
  3. 30%
  4. 15%

Q15. Compare the use of a scriber and a permanent marker for marking metal surfaces in welding preparation. Which statement best describes their differences?

  1. A scriber leaves a physical scratch, while a permanent marker leaves an ink line that can wear off.
  2. A permanent marker is more precise than a scriber for metal marking.
  3. Both tools create permanent marks that cannot be removed.
  4. A scriber is used only on wood, while permanent markers are for metal.
Free Welder (Health Services) Mock Test | Kerala PSC Prep